RF energy harvesting - usable power levels in practice?

Started by MikroTik_Fan_Will · 2026-11-09 05:13 UTC · 35 views · 4 replies
M Member
RF energy harvesting demos show microwatts in ideal conditions. What usable power have you actually harvested in a real deployment?
L Admin
RF 能量收集的「演示微瓦」到「可部署」,中间差在占空与距离。编辑部见到的现实量级:

1) 环境功率:远离基站/路由器时,可用往往是 μW 级甚至更低;能驱动的是间歇传感 + 深睡眠 MCU,不是持续射频前端。
2) 整流与匹配:宽带匹配效率差,窄带谐振效率高但对位置敏感;整流管门限决定「有信号也没直流」。
3) 验收:用已知场强(或已知发射距离)标出直流可用功率 vs 距离曲线,并写清负载电流与唤醒占空比,避免「开路电压好看」。

欢迎贴频段、距离、天线尺寸、整流拓扑和实际负载平均功耗。有「能跑多久/采几次样」的故事比峰值 μW 更有参考价值。

— rfforum 编辑部 / Editorial Team
R Member
The honest answer depends much more on distance and duty cycle than on the rectifier alone, and that is where most demos are misleading.

With a dedicated transmitter a few metres away, I have seen tens to a few hundred microwatts of usable DC power after rectification, enough for a sensor node that wakes up, takes a measurement, sends a short packet, and sleeps again. Move that same node to an ambient environment, a few metres from a Wi-Fi router or much further from a base station, and the available power usually falls to a few microwatts or less. At that level the node is not continuously powered; it is charging a capacitor or small supercapacitor for seconds or minutes, then spending the energy in a millisecond burst.

Two effects set the floor. First, rectifier efficiency collapses at low input power because of the diode threshold and the matching network loss. A rectifier that is 50 percent efficient at 0 dBm may be below 10 percent at minus 20 dBm, so quoting an open-circuit voltage tells you almost nothing. Second, a broadband match collects energy from more sources but is less efficient at any one frequency, while a narrowband resonant match is efficient only when the antenna, frequency and position are all right.

My practical test is to report the loaded DC power against distance for a known transmitter, together with the load current and the wake-up duty cycle. If the average load is 10 microwatts and the harvester delivers 5 microwatts at the deployment distance, the node will slowly lose charge no matter how good the peak number looks. If the harvester delivers 20 microwatts at that distance, the same node can run indefinitely with a sensible sleep schedule. That power-versus-distance curve, measured into a real load, is the number I trust.
L Admin
@RF_Bench_Notes — putting distance and duty cycle above rectifier brand, and trusting loaded DC vs distance + wake duty cycle (not open-circuit voltage), is the harvest honesty we will keep quoting next to every "powered a sensor from ambient RF" demo.

Editorial keepers:
1. Dedicated TX at a few metres → tens–hundreds of µW usable is a different product from ambient Wi-Fi/macro at a few µW.
2. Rectifier efficiency collapse at low Pin (your ~50% at 0 dBm → <10% at −20 dBm class) means peak/open-circuit numbers mislead.
3. Feasibility is average harvested watts vs joules-per-wake; if average load exceeds harvest at deployment distance, the node slowly dies regardless of peak.
4. Archive loaded DC vs distance + wake duty cycle on the same sheet as any "works" claim.

Open: what distance/duty-cycle sheet do you require before accepting a harvest viability claim?

— rfforum 编辑部 / Editorial Team
H Member
New here, learning a lot. Has this been validated in production?
广告 AdRenesas 瑞萨微控制器芯片产品照片Renesas Electronics微控制器、模拟与射频/时钟方案 · MCUs, analog, RF and timing访问官网 →免费展示 · 资料来自公开信息 · 如需撤下请联系 ads@rfforum.com
广告 Ad广告位招商 / Advertise hereads@rfforum.com · 刊例 Rate cardT2 · 728×90
Log in or register to reply.