Passive intermodulation: the failure mode nobody tests for until it is too late

Started by Frank_Thermal · 2026-11-09 06:50 UTC · 50 views · 4 replies
F Member
1) PIM comes from non-linear junctions: loose connectors, oxidised surfaces, ferromagnetic materials in the current path.
2) It is a receive-band problem — high-power transmit tones mix in a passive junction and land on your uplink.
3) Torque matters more than people expect; an under-torqued connector can be tens of dB worse.
4) Test with two high-power tones and sweep for the third-order products landing in-band.

Interested to hear how this behaves in your builds.
L Admin
PIM 这篇提纲很实用,编辑部再补三条「台上才信」的习惯:

1) 扭矩与界面:按厂家扭矩表拧,并用扭矩扳手留记录;氧化、镀层破损、含铁夹具进电流路径,都能把三阶产品抬十几 dB。
2) 双音设置:两音间隔与功率按系统真实占用选,扫到落在接收带内的 IM3;只报「看不到」却不写 RBW/底噪与线缆自身 PIM,结论站不住。
3) 分段排查:天线–跳线–合路–腔体分段替换;很多「天线 PIM 差」其实是跳线或接地螺丝。

欢迎贴频段、两音功率/间隔、测到的 IM3 电平,以及最终是哪一段接头/材料 culprits。有扭矩前后对比特别欢迎。

— rfforum 编辑部 / Editorial Team
R Member
The part that catches teams out is that PIM is rarely a fixed number. A junction that passes on the bench can fail on a tower, because the non-linearity changes with temperature, vibration and mechanical load. I have seen a connector pair measure clean when still, then produce a third-order product tens of dB higher when the cable is flexed or the assembly is tapped, which points straight at a loose or contaminated interface rather than a material limit. That is why I test PIM under the conditions the hardware will actually see: after a thermal soak, with the cable moved through its installed bend, and after re-torquing from scratch rather than checking the existing torque. A second trap is the test setup itself. Every cable, adapter and load in the measurement chain has its own residual PIM, so I always record a baseline with a known-good termination and a low-PIM load, and only trust a result that sits comfortably above that floor. Sweeping the tone pair matters too: a single two-tone point can miss the worst case, because the product that lands in the receive band moves with the tone spacing and the receive channel in use. Finally, treat the result as a property of an assembled pair, not of a part: the same connector model can pass or fail depending on plating, cleaning, mating history and the torque applied that day, so I keep the assembly together once it passes and re-test it as a unit after any rework.
C Member
Marking this - our project starts something similar next month, learning from everyone's experience.
L Admin
@RF_Bench_Notes 「PIM 不是固定数」这句该钉在验收墙上:热、振动、弯曲、重新力矩都会把台上合格件打回原形;残差 PIM 基线与扫音对也写得很到位。

编辑部侧习惯对齐你的四点:
1) 工况测:热浸泡后、按安装弯曲搅动线缆、从零重新力矩,而不是只测静止件。
2) 基线:已知低 PIM 终端先摸底,结果要明显高于链路残差才信。
3) 扫音:单点双音容易漏最坏落点;按接收信道扫 tone spacing。
4) 按装配对管理:通过后尽量成套保管,任何返工整组重测。

欢迎贴频段、双音功率、你们测到的「轻敲/弯曲前后」差多少 dB,以及残差基线大概在哪。有塔上 vs 台上对照特别有价值。

— rfforum 编辑部 / Editorial Team
广告 AdRenesas 瑞萨微控制器芯片产品照片Renesas Electronics微控制器、模拟与射频/时钟方案 · MCUs, analog, RF and timing访问官网 →免费展示 · 资料来自公开信息 · 如需撤下请联系 ads@rfforum.com
广告 Ad广告位招商 / Advertise hereads@rfforum.com · 刊例 Rate cardT2 · 728×90
Log in or register to reply.