L
Admin
[Technical article / FAQ, rfforum Editorial Team]
A coax adapter that looked fine on day one can cost you 0.05–0.2 dB of insertion loss after a few dozen mates — enough to fail a traveler that never recorded torque, adapter stack, or cycle count. SMA, SMP, and SMPM fail differently; treating them as interchangeable "RF connectors" is how residual gets blamed on the DUT.
1. What mate cycles actually own
- SMA production: torque (typically ~0.8–1.1 N·m for brass, lower for stainless depending on vendor) plus mating count; under-torque raises contact resistance and IL scatter, over-torque galls the outer and drifts next mates
- SMP / SMPM: float and blind-mate misalignment dominate more than torque; cycle life and detent wear move IL and return loss before the center pin looks "worn"
- Adapter stacks compound: each interface adds contact + dielectric loss; a day-one thru of three adapters is not the same thru after 40 mates on the middle joint
2. Freeze list before you blame the DUT or the VNA
- Connector family and PN at each interface in the stack (not "SMA cable")
- Torque tool / value used that day, or float/misalignment note for SMP-class
- Mate-cycle count (or "unknown — reset with known-good thru") since last inspection
- Day-check: same thru / known attenuator S21 vs the archived gate; if the thru moved, do not freeze a DUT IL number
3. Habit
Never archive a "DUT IL failed by 0.1 dB" claim without the adapter stack, torque/float note, and cycle count on the same sheet. A connector that drifted is a setup change, not a product fail.
Discussion: on your last mysterious 0.1 dB IL walk, did the fix land in re-torquing, swapping an adapter, or resetting the mate-cycle budget — and do you forbid freezing IL without a thru day-check?
— rfforum 编辑部 / Editorial Team
A coax adapter that looked fine on day one can cost you 0.05–0.2 dB of insertion loss after a few dozen mates — enough to fail a traveler that never recorded torque, adapter stack, or cycle count. SMA, SMP, and SMPM fail differently; treating them as interchangeable "RF connectors" is how residual gets blamed on the DUT.
1. What mate cycles actually own
- SMA production: torque (typically ~0.8–1.1 N·m for brass, lower for stainless depending on vendor) plus mating count; under-torque raises contact resistance and IL scatter, over-torque galls the outer and drifts next mates
- SMP / SMPM: float and blind-mate misalignment dominate more than torque; cycle life and detent wear move IL and return loss before the center pin looks "worn"
- Adapter stacks compound: each interface adds contact + dielectric loss; a day-one thru of three adapters is not the same thru after 40 mates on the middle joint
2. Freeze list before you blame the DUT or the VNA
- Connector family and PN at each interface in the stack (not "SMA cable")
- Torque tool / value used that day, or float/misalignment note for SMP-class
- Mate-cycle count (or "unknown — reset with known-good thru") since last inspection
- Day-check: same thru / known attenuator S21 vs the archived gate; if the thru moved, do not freeze a DUT IL number
3. Habit
Never archive a "DUT IL failed by 0.1 dB" claim without the adapter stack, torque/float note, and cycle count on the same sheet. A connector that drifted is a setup change, not a product fail.
Discussion: on your last mysterious 0.1 dB IL walk, did the fix land in re-torquing, swapping an adapter, or resetting the mate-cycle budget — and do you forbid freezing IL without a thru day-check?
— rfforum 编辑部 / Editorial Team
