L
Admin
[Technical article / FAQ, rfforum Editorial Team]
Turning the spectrum analyzer input attenuator down "to see the spur better" is how a mixer-generated instrument product gets written up as a DUT problem. Displayed noise falls, displayed TOI products rise, and the trace can look dirtier or cleaner for reasons that have nothing to do with the product. The attenuator is not a visibility knob; it is a mixer-level knob.
1. What the attenuator actually owns
- Input attenuator protects the first mixer and sets how hard that mixer is driven. Lower atten means more mixer level and higher internally generated harmonics and intermodulation.
- Displayed average noise improves as attenuator decreases, until the analyzer noise figure plus the DUT dominate. A "new" spur that appears only at 0 dB atten is a suspect instrument product until proven otherwise.
- A 10 dB attenuator change that moves a spur 10 dB with the carrier (spur-to-carrier ratio unchanged) is usually before the mixer — DUT or path. A spur that barely moves, that grows faster than the fundamental, or that appears only at low atten, is often the analyzer's own distortion.
2. Freeze list before you sign a spur, harmonic, or TOI claim
- Input attenuator setting, plus a plus/minus 10 dB attenuator check on the same span, RBW, and preamp state
- Preamp on or off. Preamp plus low atten on a high-level DUT is a classic false-spur machine.
- Mixer level or reference level, and whether auto-atten was allowed to change mid-sweep
- The same check with a known-clean source or a pad on the DUT. If the spur stays with the pad and still dances with atten, it is not "the PA."
3. Habit
Never archive a "DUT spur at −X dBc" without the attenuator check on the traveler. The 10 dB rule is cheap and catches most instrument IM. Do not enable the preamp and 0 dB atten together on a high-level DUT "just to see further down."
4. Practical five-minute gate
- Note the spur at the current atten. Add 10 dB input atten, and write whether you also raised the reference level.
- If the displayed spur-to-carrier ratio is unchanged, hunt in the DUT or the path before the analyzer.
- If the spur appears, grows, or jumps only at 0–10 dB atten, treat it as instrument IM until a pad or clean source proves otherwise.
Discussion: on your last mystery spur, did the 10 dB attenuator check clear it as instrument IM, or did it stay and become a real DUT hunt — and do you require that check on every spur traveler?
— rfforum 编辑部 / Editorial Team
Turning the spectrum analyzer input attenuator down "to see the spur better" is how a mixer-generated instrument product gets written up as a DUT problem. Displayed noise falls, displayed TOI products rise, and the trace can look dirtier or cleaner for reasons that have nothing to do with the product. The attenuator is not a visibility knob; it is a mixer-level knob.
1. What the attenuator actually owns
- Input attenuator protects the first mixer and sets how hard that mixer is driven. Lower atten means more mixer level and higher internally generated harmonics and intermodulation.
- Displayed average noise improves as attenuator decreases, until the analyzer noise figure plus the DUT dominate. A "new" spur that appears only at 0 dB atten is a suspect instrument product until proven otherwise.
- A 10 dB attenuator change that moves a spur 10 dB with the carrier (spur-to-carrier ratio unchanged) is usually before the mixer — DUT or path. A spur that barely moves, that grows faster than the fundamental, or that appears only at low atten, is often the analyzer's own distortion.
2. Freeze list before you sign a spur, harmonic, or TOI claim
- Input attenuator setting, plus a plus/minus 10 dB attenuator check on the same span, RBW, and preamp state
- Preamp on or off. Preamp plus low atten on a high-level DUT is a classic false-spur machine.
- Mixer level or reference level, and whether auto-atten was allowed to change mid-sweep
- The same check with a known-clean source or a pad on the DUT. If the spur stays with the pad and still dances with atten, it is not "the PA."
3. Habit
Never archive a "DUT spur at −X dBc" without the attenuator check on the traveler. The 10 dB rule is cheap and catches most instrument IM. Do not enable the preamp and 0 dB atten together on a high-level DUT "just to see further down."
4. Practical five-minute gate
- Note the spur at the current atten. Add 10 dB input atten, and write whether you also raised the reference level.
- If the displayed spur-to-carrier ratio is unchanged, hunt in the DUT or the path before the analyzer.
- If the spur appears, grows, or jumps only at 0–10 dB atten, treat it as instrument IM until a pad or clean source proves otherwise.
Discussion: on your last mystery spur, did the 10 dB attenuator check clear it as instrument IM, or did it stay and become a real DUT hunt — and do you require that check on every spur traveler?
— rfforum 编辑部 / Editorial Team
