L
Admin
[Technical article / FAQ, rfforum Editorial Team]
A 0.1–0.3 dB shift that appears after "nothing changed on the DUT" is often an adapter or ferrule story: oil, skin oils, over-torque mushrooming, or under-torque that only shows up after the next mate. The DUT did not drift; the reference plane did.
1. What actually moved
- A dirty or oxidized ferrule raises contact resistance and can add a small reflection that looks like DUT insertion-loss drift on a thru or a fixture.
- Over-torque mushrooms the female contact; under-torque leaves a intermittent contact that wanders with flex and temperature. Both can look like a "soft" DUT failure.
- Swapping one "identical" adapter mid-campaign without a re-cal or a known-good thru check invents a new residual that gets blamed on the product.
2. Freeze list before you open a DUT ECO
- Adapter PN, torque tool setting, and cycle count on that adapter stack
- A clean/inspect/re-torque A/B on the same thru, same cable, same cal — not a new DUT board
- Whether the shift survived a known-good thru or a second adapter of the same family
- Fingerprint: did the shift appear right after a mate, a flex, or a connector change?
3. Habit
Never close a 0.2 dB "DUT IL drift" without a clean + torque + thru check on the adapter stack. Archive the torque value and adapter PN next to every acceptance IL number. If cleaning and correct torque kill the delta, the DUT was never the patient.
4. Practical five-minute gate
- Inspect ferrules under light; clean per the connector family procedure
- Re-torque to the specified value with a calibrated wrench, not "hand tight plus a bit"
- Re-measure the thru; if the 0.2 dB is gone, stop the DUT hunt
Discussion: on your last mystery 0.2 dB, did the fix land in cleaning, torque, or a retired adapter — and do you require adapter PN + torque on every IL traveler?
— rfforum 编辑部 / Editorial Team
A 0.1–0.3 dB shift that appears after "nothing changed on the DUT" is often an adapter or ferrule story: oil, skin oils, over-torque mushrooming, or under-torque that only shows up after the next mate. The DUT did not drift; the reference plane did.
1. What actually moved
- A dirty or oxidized ferrule raises contact resistance and can add a small reflection that looks like DUT insertion-loss drift on a thru or a fixture.
- Over-torque mushrooms the female contact; under-torque leaves a intermittent contact that wanders with flex and temperature. Both can look like a "soft" DUT failure.
- Swapping one "identical" adapter mid-campaign without a re-cal or a known-good thru check invents a new residual that gets blamed on the product.
2. Freeze list before you open a DUT ECO
- Adapter PN, torque tool setting, and cycle count on that adapter stack
- A clean/inspect/re-torque A/B on the same thru, same cable, same cal — not a new DUT board
- Whether the shift survived a known-good thru or a second adapter of the same family
- Fingerprint: did the shift appear right after a mate, a flex, or a connector change?
3. Habit
Never close a 0.2 dB "DUT IL drift" without a clean + torque + thru check on the adapter stack. Archive the torque value and adapter PN next to every acceptance IL number. If cleaning and correct torque kill the delta, the DUT was never the patient.
4. Practical five-minute gate
- Inspect ferrules under light; clean per the connector family procedure
- Re-torque to the specified value with a calibrated wrench, not "hand tight plus a bit"
- Re-measure the thru; if the 0.2 dB is gone, stop the DUT hunt
Discussion: on your last mystery 0.2 dB, did the fix land in cleaning, torque, or a retired adapter — and do you require adapter PN + torque on every IL traveler?
— rfforum 编辑部 / Editorial Team
