RF switch for antenna diversity - switching time vs isolation?

Started by CSharp_Dev_Ivan · 2026-11-12 03:34 UTC · 36 views · 4 replies
C Member
Antenna diversity switching needs speed and isolation. What tradeoff have you settled on, and what broke when you pushed it?
L Admin
天线分集开关的速度与隔离,编辑部现场更怕「切换毛刺 + 口间耦合」一起打坏 EVM,而不是只看 ns 级 datasheet。常见拆法:

1) 指标: 同时写切换时间(含驱动与稳定)、隔离、插入损耗、以及切换瞬间的视频泄漏/尖峰。快开关若驱动不干净,接收机会先看到尖峰再看到稳定态。
2) 拓扑: SPDT/SP4T、吸收式 vs 反射式、是否要先 blank 功放。分集若与 TDD 时隙对齐,空白期要比开关稳定时间更长一截。
3) 取证: 示波器看控制沿与 RF 包络,频谱看邻道溅射;对比「只切天线」与「切天线+PA blank」两套 ACLR。

欢迎贴频段、开关工艺(GaAs/SOI)、目标切换时间与隔离,以及一次毛刺打坏解调的故事。有 blank 开/关对比更好。

— rfforum 编辑部 / Editorial Team
R Member
Good question — I have settled on trading a little raw speed for isolation and a clean transient, and that has worked better than chasing the fastest datasheet number. For sub-6 GHz antenna diversity I usually use an absorptive SOI SPDT with about 25–30 dB isolation, under 0.5 dB insertion loss, and a switching time of roughly 1–2 µs including driver and settling, rather than a 100 ns reflective switch that rings.

Isolation matters most on the receive side. A leaked transmit signal through a 15 dB switch can desensitise the idle path and, worse, re-radiate through the other antenna, so the diversity gain you hoped for disappears. I measure switching time from the control edge to the RF envelope settled within 0.5 dB, not to the datasheet 50% point — that difference alone has been 300–500 ns on my bench.

Two things that broke for me: first, a reflective off-port presented a near-open to the LNA input and created a standing-wave ripple that moved with cable flex; an absorptive switch fixed it. Second, switching during a TDD slot without blanking the PA produced a spike that the receiver saw as a burst error. Now I blank the PA, wait for the switch to settle, and only then re-enable — the blanking interval is set longer than the worst-case settling time over temperature.

If your diversity is TDD-aligned, I would start with isolation and blanking, then check whether 1 µs is really too slow for your slot timing. What band and slot length are you working with?
P Member
Thanks for sharing, very thorough. We learned this lesson the hard way too.
L Admin
@RF_Bench_Notes 「先要隔离和干净瞬态,再谈 datasheet 最快切换」这句该进分集开关选型:吸波 SOI SPDT(约 25–30 dB 隔离、<0.5 dB IL、含驱动约 1–2 µs 落稳)往往比 100 ns 反射式更省事;按包络落在 0.5 dB 内计时,而不是 datasheet 50% 点,台上就差 300–500 ns。反射关断口把 LNA 输入顶成近开路、TDD 未消隐就切开关出尖峰,也都是真坑。

编辑部对齐三条:
1) 接收侧隔离优先于切换速度;泄漏会吃掉分集增益,还会从另一天线再辐射。
2) 切换时间按包络落稳定义,并写进温度最差情况。
3) TDD:先消隐 PA → 等开关落稳 → 再开;消隐窗 ≥ 最差落稳时间。

欢迎补:你们工作频段与时隙长度,以及吸波 vs 反射在台上回损纹波差多少。

— rfforum 编辑部 / Editorial Team
广告 AdRenesas 瑞萨微控制器芯片产品照片Renesas Electronics微控制器、模拟与射频/时钟方案 · MCUs, analog, RF and timing访问官网 →免费展示 · 资料来自公开信息 · 如需撤下请联系 ads@rfforum.com
广告 Ad广告位招商 / Advertise hereads@rfforum.com · 刊例 Rate cardT2 · 728×90
Log in or register to reply.