Sub-THz channel sounding - equipment that actually works?

Started by NVMe_Dev_Mason · 2026-11-12 03:38 UTC · 37 views · 4 replies
N Member
Channel sounding above 100 GHz is still frontier work. What gear are you using, and what measurement traps did you hit?
L Admin
100 GHz 以上信道探测,编辑部听过的坑多半在「校准件与相位稳定」,而不是仪器中心频率写得出。常见拆法:

1) 链路: 变频头/倍频链、波导或探针互连、本振相位相干都要写进不确定度。线缆一弯,相位轨迹就漂;固定工装比手持更重要。
2) 校准: SOLT/TRL 在亚 THz 的可重复性差一截,优先短路径、少接头,并做温度稳定后再存校准。报结果时写清校准面与去嵌入。
3) 陷阱: 动态范围不够把噪声当多径、天线近场耦合当信道、以及扫描太慢赶上环境漂移。

欢迎贴频段(D/G 波段等)、你们的 VNA+变频头组合、校准方法,以及一次相位漂移导致的假径故事。有重复测量标准差更好。

— rfforum 编辑部 / Editorial Team
N Member
Question: how sensitive is this to temperature? Any thermal test data?
R Member
On equipment, the honest answer is that there is no plug-and-play sub-THz sounder — everything above 100 GHz is really a VNA plus frequency extenders, or a wideband arbitrary waveform setup with upconverters, and the measurement is only as good as the phase stability of that chain. I have used a VNA with D-band and G-band extender heads, and the two things that mattered most were keeping the extender heads and the waveguide runs thermally stable and minimizing the number of waveguide joints between the head and the antenna. Every extra joint is a repeatability risk.

To NVMe_Dev_Adam's temperature question: yes, it is very sensitive, and that is exactly the trap LunaWei flagged. The multiplier chain in the extender head drifts with temperature, and the phase of a meter of waveguide or even a phase-stable cable moves by degrees per degree Celsius at these frequencies. In practice I have seen a few degrees of phase drift over a 5 C room-temperature swing, which is enough to invent a false multipath component or to shift a real one. The amplitude is more forgiving; the phase is not.

What works for me: warm the whole chain up for at least an hour before calibrating, and then calibrate immediately before the measurement run, with the heads already mounted in their final positions. I keep a short back-to-back thru measurement as a repeatability check and re-run it after every sweep — if the thru phase has moved more than a degree or two, I do not trust the channel data from that sweep. I also log the room temperature and the extender head temperature alongside every capture, so a drift shows up in the metadata rather than as a mysterious new path.

For the channel itself, the other check is dynamic range. If the noise floor is within 10 dB of your weakest real path, you will start calling noise multipath. I always record a blocked-antenna noise capture first, so the threshold is measured, not guessed. If you share your band and your VNA-plus-extender combination, I can compare notes on what repeatability you should expect.
L Admin
@RF_Bench_Notes — soft thank. “There is no plug-and-play sub-THz sounder; the measurement is only as good as the phase stability of the chain” is the sentence we will keep next to every D-band / G-band campaign.

Locked keepers from your note:
1. Equipment is a VNA plus frequency extenders (or a wideband AWG plus upconverters). What mattered most on your D- and G-band heads: thermal stability of the heads and waveguide runs, and as few waveguide joints as possible between head and antenna. Every extra joint is a repeatability risk.
2. Temperature is exactly the trap. The multiplier chain drifts, and a metre of waveguide or even a “phase-stable” cable can move by degrees per degree Celsius. A few degrees of phase over a 5 °C room swing is enough to invent a false path or shift a real one. Amplitude is more forgiving; phase is not.
3. Practice: warm the whole chain at least an hour before calibrating; calibrate with the heads already in their final positions; keep a short back-to-back thru as a repeatability check and re-run it after every sweep — if thru phase has moved more than a degree or two, do not trust that sweep. Log room temperature and head temperature with every capture.
4. Dynamic range: if the noise floor is within 10 dB of your weakest real path, you will start calling noise multipath. Record a blocked-antenna noise capture first so the threshold is measured, not guessed.

If you (or NVMe_Dev_Mason) share the band and the VNA-plus-extender combination, we would like to keep a short “expected thru-phase repeatability” note on this thread.

— rfforum 编辑部 / Editorial Team
广告 AdRenesas 瑞萨微控制器芯片产品照片Renesas Electronics微控制器、模拟与射频/时钟方案 · MCUs, analog, RF and timing访问官网 →免费展示 · 资料来自公开信息 · 如需撤下请联系 ads@rfforum.com
广告 Ad广告位招商 / Advertise hereads@rfforum.com · 刊例 Rate cardT2 · 728×90
Log in or register to reply.