GaN PA datasheet CW vs pulsed: the Psat that only exists at 10% duty

Started by LunaWei · 2026-11-14 01:53 UTC · 39 views · 3 replies
L Admin
[Technical article / FAQ, rfforum Editorial Team]

A GaN PA datasheet that quotes a high Psat or efficiency often does it under pulsed conditions. Dropping that number into a CW link budget is how a thermal and efficiency miss gets blamed on "process variation." CW and pulsed are different products until the duty, pulse width, and case temperature are written next to the claim.

1. What the footnotes hide
- Pulsed Psat at 10% duty with a short pulse can be 1–3 dB above what the same die delivers in CW at the same case temperature, because the junction never reaches the CW thermal state.
- Efficiency and ACLR footnotes often assume a pulse train or a specific load; CW modulated drive at the same average power is a different thermal and trapping story.
- "Typical" vs "minimum" and the case-temperature reference (25 °C fixture vs derated hot) change the number you are allowed to design to.

2. Freeze list before you freeze a link budget
- Duty cycle, pulse width, and whether the Psat/efficiency line is CW or pulsed
- Case or flange temperature for that line; your heat sink vs the datasheet fixture
- Whether your waveform average power and PAPR match the datasheet test, not only the peak
- Derating: hot CW at your flange temp, not brochure room-temp pulsed

3. Habit
Never paste a datasheet Psat into a CW budget without duty and temperature in the same cell. Archive CW vs pulsed note, duty, and flange temp next to every power claim. If the datasheet is pulsed-only, measure or derate before you promise CW EIRP.

4. Practical gate
- Highlight CW vs pulsed on the datasheet page you design from
- Ask the vendor for CW Psat/efficiency at your flange temperature, or measure it
- Budget thermal headroom explicitly; do not hide it in "implementation loss"

Discussion: on your last GaN power miss, how much was CW-vs-pulsed vs heat sink — and do you require duty + temperature on every datasheet number that enters a budget?

— rfforum 编辑部 / Editorial Team
L Admin
Addendum — GaN power traveler: duty cycle, pulse width, and case or flange temperature in the same cell as any Psat or efficiency number that enters a link budget. A brochure pulsed Psat at 10% duty is a different thermal and trapping state from CW at your heat sink.

If the datasheet is pulsed-only, measure or derate at your flange temperature before promising CW EIRP. “Typical” versus “minimum,” and 25 °C fixture versus your hot case, belong on the same line. Do not hide the thermal gap in “implementation loss.”

Open: on your last GaN power miss, how much was CW-versus-pulsed versus the heat sink — and do you require duty + temperature on every datasheet number that enters a budget?

— rfforum 编辑部 / Editorial Team
F Member
【Editorial Discussion】

The original post is right to refuse a pulsed Psat pasted into a CW budget without duty and flange temperature in the same cell. A further distinction is worth making once that row is honest: even at the same average power and case temperature, trapping and the bias network can make pulsed and CW behave like different devices.

Current collapse and related trap time constants may still be recovering inside a short pulse, so the pulse peak is not the CW compression point at the same flange temperature. If the datasheet pulse is much shorter than those time constants, derating by a single fixed number may still be unconservative — or, occasionally, overly pessimistic — unless you measure at the pulse width and duty you will actually use. The bias-feed impedance also differs: a network that is quiet in a short pulse can ring or droop in CW and in a long pulse train, moving both power and linearity.

A practical addition to the traveler is therefore: pulse width versus the estimated thermal and trap time constants, and a CW (or long-pulse) confirmation at the intended average power, not only a duty-cycle footnote. If you cannot get a CW curve, say so in the budget rather than hiding the gap in implementation loss.

We would be interested in how you decide when a pulsed line is even eligible for derating, versus when you insist on a CW measurement before the number enters a link budget.
C Member
How's the power consumption on this? Our project has a tight power budget.
广告 AdRenesas 瑞萨微控制器芯片产品照片Renesas Electronics微控制器、模拟与射频/时钟方案 · MCUs, analog, RF and timing访问官网 →免费展示 · 资料来自公开信息 · 如需撤下请联系 ads@rfforum.com
广告 Ad广告位招商 / Advertise hereads@rfforum.com · 刊例 Rate cardT2 · 728×90
Log in or register to reply.