L
Admin
[Technical article / FAQ, rfforum Editorial Team]
A near-field scan that reports ugly cross-pol at one cut can be the probe, not the antenna under test. Probe polarization purity, alignment, and cable twist invent a pattern that survives every AUT remount while the real far-field cross-pol is fine.
1. What the probe owns
- A probe with finite axial ratio or imperfect linear purity couples a fraction of the orthogonal field into the wanted channel. That fraction maps into a false cross-pol floor that moves with probe rotation more than with AUT rotation.
- Cable twist and connector clocking between the probe and the receiver change the apparent polarization reference. A "new" cross-pol lobe that appears after a cable swap is a reference-plane story until proven otherwise.
- Sampling density and probe height couple into the same error: undersampling aliases a probe sidelobe into the AUT map.
2. Freeze list before you redesign the AUT
- Probe PN, measured or datasheet polarization purity / axial ratio at the test frequency, and last alignment check
- A 90-degree probe roll: if the false cross-pol rotates with the probe, stop blaming the AUT
- Cable clocking note and a remate with a marked connector orientation
- Compare one cut against a known-good linearly polarized standard or a far-field spot check at the same frequency
3. Habit
Never freeze "AUT cross-pol fail" from a single near-field campaign without a probe-roll and cable-clock note. Archive probe purity and a standard-antenna cut next to every cross-pol claim. If the lobe follows the probe, the AUT was never the patient.
4. Practical five-minute gate
- Mark cable keying; remate once and re-cut
- Roll the probe 90 degrees; note whether the suspect lobe moves
- Spot-check one angle in far-field or with a second probe
Discussion: on your last stubborn cross-pol cut, did the fix land in probe purity, cable clocking, or a real AUT feed — and do you require a probe-roll before opening an AUT ECO?
— rfforum 编辑部 / Editorial Team
A near-field scan that reports ugly cross-pol at one cut can be the probe, not the antenna under test. Probe polarization purity, alignment, and cable twist invent a pattern that survives every AUT remount while the real far-field cross-pol is fine.
1. What the probe owns
- A probe with finite axial ratio or imperfect linear purity couples a fraction of the orthogonal field into the wanted channel. That fraction maps into a false cross-pol floor that moves with probe rotation more than with AUT rotation.
- Cable twist and connector clocking between the probe and the receiver change the apparent polarization reference. A "new" cross-pol lobe that appears after a cable swap is a reference-plane story until proven otherwise.
- Sampling density and probe height couple into the same error: undersampling aliases a probe sidelobe into the AUT map.
2. Freeze list before you redesign the AUT
- Probe PN, measured or datasheet polarization purity / axial ratio at the test frequency, and last alignment check
- A 90-degree probe roll: if the false cross-pol rotates with the probe, stop blaming the AUT
- Cable clocking note and a remate with a marked connector orientation
- Compare one cut against a known-good linearly polarized standard or a far-field spot check at the same frequency
3. Habit
Never freeze "AUT cross-pol fail" from a single near-field campaign without a probe-roll and cable-clock note. Archive probe purity and a standard-antenna cut next to every cross-pol claim. If the lobe follows the probe, the AUT was never the patient.
4. Practical five-minute gate
- Mark cable keying; remate once and re-cut
- Roll the probe 90 degrees; note whether the suspect lobe moves
- Spot-check one angle in far-field or with a second probe
Discussion: on your last stubborn cross-pol cut, did the fix land in probe purity, cable clocking, or a real AUT feed — and do you require a probe-roll before opening an AUT ECO?
— rfforum 编辑部 / Editorial Team
