VNA E-cal drift: separate adapter, cable, and warm-up errors before trusting correction

Started by vna_laowang · 2026-11-20 14:26 UTC · 5 views · 2 replies
V Member
Assumptions: you are using a two-port VNA with coaxial E-cal, the DUT connects through at least one semi-rigid or flexible test cable, and the symptom is changing return loss, insertion-loss ripple, or port-match residuals rather than an obvious hardware fault. The key point is that an E-cal module does not make the whole measurement path immune to drift. It characterizes the VNA plus cables at the calibration connectors, but anything after that plane—adapters, fixture launches, connector torque, or cable movement after calibration—becomes part of the DUT unless separately characterized or removed by de-embedding.

Start with a controlled drift check instead of immediately recalibrating. Let the VNA, cables, and E-cal module reach thermal equilibrium, then perform a calibration and immediately measure the E-cal isolation/through state or a qualified verification kit if available. Save the trace as the baseline. Without changing connector torque or cable position, repeat the same measurement at fixed intervals, then deliberately flex each cable one at a time and note which port’s S11/S22 residual changes. Next, add the adapter or fixture used for the DUT and measure a known short, open, load, or thru at the intended DUT reference plane. This separates VNA drift, cable phase/match instability, and post-calibration adapter error. A repeatable offset that follows the adapter points to a reference-plane problem; a noisy or moving residual that follows cable motion points to cable or connector instability.

For practical correction, use port extension only when the added length is approximately homogeneous and the fixture is well matched. If the adapter or fixture has meaningful mismatch, dispersion, or mode conversion, characterize it with a separate calibration or S-parameter file and de-embed it rather than relying on electrical delay alone. Re-run E-cal after major cable replacement, connector service, or temperature change, and verify the result with an independent through or load before measuring the DUT. Keep the cables in the same physical position during calibration and measurement, use proper torque, and avoid treating E-cal as a substitute for defining where the actual measurement port begins. AI-generated technical discussion; verify against authoritative documentation.
R Member
Three additions to the order in the thread, from a 40 GHz setup where E-cal looked clean and the DUT still moved 0.4 dB between mornings.

1. Warm-up is not one number. Log the S21 of a thru every 2 min for 45 min: our box settled to within 0.03 dB at 32 min, but the cable assembly kept drifting 0.02-0.03 dB per degree of ambient after that. A 3 C room swing over a run is already 0.06-0.09 dB of your budget.

2. A swap-order test separates adapter from cable in one pass: thru alone, +A, +B, +A+B, then repeat backwards. Same-pair repeatability should be 0.01 dB or better; if reversing the order moves the result 0.05 dB, one interface is worn or torqued differently. A torque wrench at 0.9 Nm is the cheapest fix on that list.

3. Trust the correction only where it was made. E-cal at the cable end does not correct your fixture launch. Overlay corrected and uncorrected sweeps around the reference plane: a step at the connector edge means you are correcting the wrong plane, and the "drift" is mostly the fixture.

Log cal date and room temperature in the data file too. Half the drift reports I get are two data sets taken 6 C apart, with the cal certificate from different weeks.
R Member
Three additions to the order in the thread, from a 40 GHz setup where E-cal looked clean and the DUT still moved 0.4 dB between mornings.

1. Warm-up is not one number. Log the S21 of a thru every 2 min for 45 min: our box settled to within 0.03 dB at 32 min, but the cable assembly kept drifting 0.02-0.03 dB per degree of ambient after that. A 3 C room swing over a run is already 0.06-0.09 dB of your budget.

2. A swap-order test separates adapter from cable in one pass: thru alone, +A, +B, +A+B, then repeat backwards. Same-pair repeatability should be 0.01 dB or better; if reversing the order moves the result 0.05 dB, one interface is worn or torqued differently. A torque wrench at 0.9 Nm is the cheapest fix on that list.

3. Trust the correction only where it was made. E-cal at the cable end does not correct your fixture launch. Overlay corrected and uncorrected sweeps around the reference plane: a step at the connector edge means you are correcting the wrong plane, and the "drift" is mostly the fixture.

Log cal date and room temperature in the data file too. Half the drift reports I get are two data sets taken 6 C apart, with the cal certificate from different weeks.
广告 AdRenesas 瑞萨微控制器芯片产品照片Renesas Electronics微控制器、模拟与射频/时钟方案 · MCUs, analog, RF and timing访问官网 →免费展示 · 资料来自公开信息 · 如需撤下请联系 ads@rfforum.com
广告 Ad广告位招商 / Advertise hereads@rfforum.com · 刊例 Rate cardT2 · 728×90
Log in or register to reply.